Flashing gateware and Linux image#

In this tutorial we are going to learn to flash the gateware image to FPGA and sdcard.image to eMMC storage.

Important

Additional hardware required:

FlashPro5/6 programmer
Tag connect TC2050-IDC-NL 10-Pin No-Legs Cable with Ribbon connector
TC2050-CLIP-3PACK Retaining CLIP board for TC2050-NL cables

Programming & Debug tools installation#

To flash a gateware image to your BeagleV-Fire board you will require a FlashPro5/6 and FlashPro Express (FPExpress) tool which comes pre-installed as part of Libero SoC Design Suite. A standalone FlashPro Express tool is also available with MicroChip’s Programming and Debug Tools package, which we are going to use for this tutorial. Below are the steps to install the software:

Download the zip for your operating system from Programming and Debug Tools page.
Unzip the file and in the unzipped folder you will find launch_installer.sh and Program_Debug_v2023.1.bin.
Execute the launch_installer.sh script to start the installation procedure.

[lorforlinux@fedora Program_Debug_v2023.1_lin] $ ./launch_installer.sh

No additional packages to install for installer usage

Requirement search complete.

See /tmp/check_req_installer608695.log for information.

Launch of installer
Preparing to install
Extracting the JRE from the installer archive...
Unpacking the JRE...

Note

It’s recommended to install under home/user/microchip for linux users.

Enabling non-root user to access FlashPro#

Download 60-openocd.rules
Copy udev rule sudo cp 60-openocd.rules /etc/udev/rules.d
Trigger udevadm using sudo udevadm trigger or reboot the PC for the changes to take effect

Flashing gateware image#

Note

content below is valid for beta testers only.

Launch FPExpress#

Download FlashProExpress.zip file and unzip, it contains the *.job file which we need to create a new project in FPExpress.
Open up a terminal and go to /home/user/microchip/Program_Debug_v202X.Y/Program_Debug_Tool/bin which includes FPExpress tool.
Execute ./FPExpress in terminal to start FlashPro Express software.

Create new project#

Important

Make sure you have your FlashPro5/6 connected before you create a new project.

Press CTRL+N to create a file and you will see a pop-up window like shown below,

Fig. 484 FPExpress new project creation window#

Follow the steps below as annotated in the image above:

Click on browse (1) button to select the job file.
Click on browse (2) button to select the project location.
Click ok button to finish.

If your FlashPro5/6 is connected properly you’ll see the window shown below:

Fig. 485 FPExpress new project flash window#

Following the annotation in the image above:

From drop-down select Program action
Click on RUN button
Shows the progress

If you see a lot of green color and the progress bar says PASSED then well done you have successfully flashed the gateware image on your BeagleV-Fire board.

Flashing eMMC#

Connect to BeagleV-Fire UART debug port using a 3.3v USB to UART bridge.

Now you can run tio <port> -b 115200 in a terminal window to access the UART debug port connection. Once you are connected properly you can press the Reset button which will show you a progress bar like in the

Fig. 487 BeagleV-Fire booting HSS with progress bar#

Once you see that progress bar on your screen you can start pressing any button (0-9/a-z) which will stop the board from fully booting and you’ll be able to access Hart Software Services (HSS) prompt. BeagleV-Fire’s eMMC content is written by the Hart Software Services (HSS) using the usbdmsc command. The HSS usbdmsc command exposes the eMMC as a USB mass storage device USB type C connector.

Fig. 488 BeagleV-Fire boot messages with HSS prompt access#

Once you see >> you can execute the commands below:

>> mmc
>> usbdmsc

Fig. 489 HSS commands to show eMMC as mass storage#

After executing the commands above your BeagleV-Fire’s eMMC will be exposed as a mass storage device like shown in the image below:

Fig. 490 BeagleV-Fire eMMC as mass storage#

Once your board is exposed as a mass storage device, you can proceed to flash the sdcard.img on your BeagleV-Fire’s eMMC.

This document outlines two methods to flash from your local machine to BeagleV Fire’s eMMC.

1. First method is to use Balena Etcher software. This software can be used to flash image in either Windows or Linux operating system.

Select image

Select the sdcard.img file from your local drive storage.
Click on select target.

Select Target

Select MCC PolarFireSoC_msd as target.
Click Select(1) to proceed.

Fig. 492 Balena Etcher selecting target#

Flash image

Click on Flash! to flash the sdcard.img on BeagleV-Fire eMMC storage.

Second method is suitable for flashing the image using Linux machine via the command line.

sudo dd if=output/images/sdcard.img of=/dev/sdX bs=1M status=progress

Note

You need to replace /dev/sdX with the actual device name of your eMMC. Use tools like dmesg, lsblk, or GNOME Disks before and after exposing your device as a USB to identify the correct device name. Be very careful not to overwrite the wrong drive, as this action is irreversible.

Once the transfer is complete, type CTRL+C to disconnect your device
Finally boot the new Linux image by typing boot or reset your board

Congratulations! with that done you have fully updated BeagleV-Fire board with up to date gateware image on it’s PolarFire SoC’s FPGA Fabric and linux image on it’s eMMC storage.

License Terms